Tel.: +49 - 2102 - 486 - 612 0
Fax: +49 - 2102 - 486 - 709 0
edm.sales@meg.mee.com


MV-R Series

Technical data

MV1200R MV2400RMV2400R MV4800R
Machine MV1200R Connect MV2400R Connect MV2400R Z+ Connect MV4800R Connect
Travel (X / Y / Z) in mm 400 / 300 / 220 600 / 400 / 310 600 / 400 / 425 800 / 600 / 310
Travel (U / V) in mm 120 / 120 150 / 150 150 / 150 (+/- 75) 150 / 150 (+/- 75)
Taper angle (workpiece height) in °/mm 15 / 200  30 / 87 15 / 260  30 / 110 15 / 260  30 / 110 15 / 260  30 / 110
Max. workpiece dimensions (W x D x H) in mm 810 x 700 x 215 1050 x 820 x 305 1050 x 820 x 420 1250 x 1020 x 305
Max. workpiece weight in kg 500 1500 1500 3000
Table dimensions (W x D) in mm 640 x 540 840 x 640 840 x 640 1080 x 780
Table layout Hardened 4-sided frame table Hardened 4-sided table
Possible wire diameters in mm 0.1 – 0.,3 0.15–0.3
Wire spool capacity in kg 10 10 / 16 / 20 / 25
Automatic wire threader / wire chopper Yes / Yes
Overall dimensions (W x D x H) in mm 2025 x 2760 x 2015 2687 x 3030 x 2150 2837 x 3452 x 2380 3100 x 3475 x 2415
Machine weight in kg 2700 3500 3650 5600
Mains voltage 3-phase 400 V/AC ± 10 %, 50/60 Hz, 13 kVA

 

Filter system MV1200R Connect MV2400R Connect MV2400R Z+ Connect MV4800R Connect
Tank capacity in l 550 860 980 1480
Filter particle size in µm / filter elements 3/2
Temperature control Dielectric cooling unit
Weight (dry) in kg Included in machine weight 350 390 450

 

Generator MV1200R Connect MV2400R Connect MV2400R Z+ Connect MV4800R Connect
Power supply unit Regenerative transistor pulse type
Cooling method Fully sealed / indirect air cooling
Max. output current in A 50
Dimensions (W x D x H) in mm 600 x 650 x 1765
Weight in kg 240

 

Control MV1200R Connect MV2400R Connect MV2400R Z+ Connect MV4800R Connect
Input method Keyboard, USB flash drive, Ethernet, 19” touchscreen
Control system CNC, closed circuit
Min. command step (X / Y / Z / U / V) in µm 0.1
Min. axis resolution in µm 0.05

 

Equipment MV1200R Connect MV2400R Connect MV2400R Z+ Connect MV4800R Connect
Tubular Shaft Drives with linear scales (X / Y / U / V) Yes
Control M800 with 19” full-touch monitor Yes
Hand pilot with configurable LCD monitor Yes
Automatic vertical front door Yes
Digital AE II generator Yes
Fine finishing generator H-FS Yes
Digital electricity meter / filter pressure sensor Yes
Ethernet/DNC/FTP Yes
Preparation for automation Yes Not available
McAfee AntiVirus embedded Yes
Production data output Yes
3D CamMagic on-board Yes
Corehold technology Yes
Job scheduler Yes
Sleep mode Yes
Optionale Hardware MV1200R Connect MV2400R Connect MV2400R Z+ Connect MV4800R Connect
Digital fine finishing generator D-FS Optional (not retrofittable) Not available
Thin wire specification 0.05 / 0.07 mm Optional (not retrofittable) Not available
Wire station for 16 / 20 / 25 kg wire spools Optional
Wire station for 50 kg wire spools Optional
Angle Master Advance II – basic kit including aligning device Optional
Angle Master advance II – wire feed set Optional
Automatic Renishaw probe on sleeve Optional
ERGO LUX LED floodlight Optional
Tricolour status lamp Optional
Automatic dielectric water refilling Optional
Connection to external cooling system Optional
External signal output with relay board Optional
Optional tools MV1200R Connect MV2400R Connect MV2400R Z+ Connect MV4800R Connect
mcAnywhere Control / mcAnywhere Control light Optional
mcAnywhere Contact / mcAnywhere Contact light Optional/Yes
mcAnywhere Service Yes
Tool package / automation solutions Optional

Power connection: 3-phase 400 V/AC, PE, ± 10%, 50/60 Hz, primary fuse 32 A slow Pneumatic connection: 5–7 kgf/cm³, 500–700 kpa, minimum air flow rate 75 l/min, 3/8" hose connection The EDM system should be set up on a suitable hard industrial floor and preferably on a consolidated concrete floor. Any shielding that may be necessary in conformity with the EMC Directive is not included in the equipment supplied by Mitsubishi Electric. The cooling unit contains fluorinated greenhouse gas R410A. For further information, please refer to the associated operating instructions.




  • Thread that?

    See for yourself!

    Again threading the wire breakage position, with and without water jet, even in difficult applications.

    learn more
  • Yes, hovers!

    No friction, no wear!

    The Tubular direct drive converts energy directly in movement - without touch, without maintenance and above all without loss of precision in the long term.

    learn more
  • Pays off!

    Euro for Euro...

    An EDM machine that responds quickly and accurately, more quickly reach better surface quality.

    learn more


Contact us now / Get a Quote






Mitsubishi Electric Europe B.V.
Branch of Germany
Mitsubishi-Electric-Platz 1
D-40882 Ratingen

Tel.: +49 2102 486-6120
Fax: +49 2102 486-7090

edm.sales@meg.mee.com




MV-R Connect Quick Facts

MV-R Connect Series
  • Travel: 800 / 600 / 310
  • Workpiece dims.: 1250 x 1020 x 305

More Specifications


Customer opinion

Rolf Hauss

The wire-cutting machines from Mitsubishi come into play when we need parts, i.e. cuts, corners and radii, that aren’t easy to produce with conventional machining.

Rolf Hauss (Project Manager)
TECHTORY Automation GmbH

To the Movie / Article


Brochure


Transport and setup